Search results

Page title matches

  • ==Programming Mimosa chips==
    5 KB (759 words) - 18:14, 23 February 2012
  • ...(MATLAB executables) are used to call large pre-existing C/C++ and Fortran programs from MATLAB without translating them into MATLAB. Another advantage is tha To understand how to use MEX-Files to Call C/C++ and Fortran Programs see
    5 KB (589 words) - 07:58, 8 February 2011

Page text matches

  • ==Programming T&T== #*[[Using MEX-Files to Call C/C++ and Fortran Programs]]
    255 bytes (43 words) - 09:59, 19 January 2011
  • ...hall be part of the ELIPS-3 program and allocated funding to ASIM from the program. A flight model of the ASIM payload will be built through Phase C/D startin
    883 bytes (130 words) - 14:09, 10 January 2011
  • ...art meny), the tutorial contains a detailed description on what to do. The program this tutorial is designed for is called XJDeveloper 3.10. ...properly connected and that the license is set correctly. You can open the program from the XJ-icon on the right side of the windows taskbar. If everything is
    1,011 bytes (163 words) - 16:41, 22 February 2021
  • ==Compiling programs== To compile your own Fortran program written with DarkSusy, the call should be similar to (if you've configured
    2 KB (280 words) - 08:56, 12 March 2012
  • ...(MATLAB executables) are used to call large pre-existing C/C++ and Fortran programs from MATLAB without translating them into MATLAB. Another advantage is tha To understand how to use MEX-Files to Call C/C++ and Fortran Programs see
    5 KB (589 words) - 07:58, 8 February 2011
  • This tutorial requires a multi-core micro processor system that can be programmed by Xilinx SDK. It also assumes that the user has two working independent Click Apply, and run. This should program the processor over JTAG, and both applications should be up and running.
    2 KB (297 words) - 15:19, 4 January 2018
  • At this point connect your NEXY4 board . In the left menu under “program and debug”, click open target => open new target Now you can program your device, click program device and choose your FPGA
    3 KB (539 words) - 13:26, 15 September 2017
  • 1. Open up a command prompt window (Start Menu > All Programs > Accessories > Command Prompt). ...re the activity light starts to flash on the FlashPro4. Don't despair, the program is probably not crashed.
    4 KB (668 words) - 12:11, 15 September 2017
  • * regular programs: [http://www.busybox.net/about.html BusyBox], The Swiss Army Knife of Embe ...commands like od, cmp and diff. An additional package contains those three programs. To install them
    6 KB (1,086 words) - 14:16, 15 April 2010
  • At this point connect your NEXY4 board . In the left menu under “program and debug”, click open target => open new target Now you can program your device, click program device and choose your FPGA
    5 KB (798 words) - 22:16, 2 March 2016
  • [[Category:Programming]]
    832 bytes (136 words) - 09:51, 20 May 2016
  • == Programming == A FlashPro project including a STAPL programming file with firmware and u-boot images can be found [http://tidsreise.com
    7 KB (1,036 words) - 13:11, 24 July 2014
  • From the busybox DCS board, you find some bitfiles to program and setup the Busybox under: You can program the busybox with the program.sh script:
    5 KB (861 words) - 14:28, 21 August 2009
  • ...entical charge signal when struck by a photon. The programs shown here are programs to test all the pixels on a MPPC. A program for the Zecotec MAPD (briefly tested) are also presented at the end.
    17 KB (3,153 words) - 11:09, 29 November 2010
  • 11. Choose <i>Tools -> Programmer</i>. Now choose JTAG as MODE. To make your programming file come through the scan chain, you have to add the device EPM7256B. ...terrupt-driven DMA-transfers. A signal handler located in the generate_irq program will respond to the interrupts.
    8 KB (1,411 words) - 12:11, 15 September 2017
  • ...og grei når man skal gjøre enkle ting, men man kan også kjøre noen større programmer som f.eks. maple og matlab (disse virker i både tekst mode og grafisk m Om du prøver å kjøre et grafisk (X) program, f.eks. xmaple eller xclock, vil du få en feilmelding som dette:
    2 KB (405 words) - 14:11, 17 February 2010
  • ...the hardware, to control the main operation modes of the Actel FPGA and to program the Flash memory for the Active Partial Reconfiguration solution to work. ...ctive Partial Reconfiguration solution to work, the Flash memory has to be programmed with the correct firmware for the Xilinx FPGA.
    18 KB (2,882 words) - 10:49, 20 February 2009
  • * [https://reference.digilentinc.com/vivado Vivado - Xilinx Programming Environment - Board files, reference projects, etc]
    1 KB (177 words) - 14:54, 2 March 2020
  • After entering into XMD prompt window, using "fpga -f" command to program Virtex FPGA: ...the JTAG chain, use "-debugdevice devicenr" to specify the component to be programmed, here we need to configure one Virtex6 and two Spartan6 FPGAs:
    18 KB (2,886 words) - 17:56, 8 April 2014
  • == install/update program with install manager == ...CDROM1 folder. *Check that there isn't a slash at the end of the path. The program doesn't search recursively.
    12 KB (2,005 words) - 13:31, 15 September 2017
View (previous 20 | ) (20 | 50 | 100 | 250 | 500)